9.3.10. Dismantling and assembly of transmission
Section 1
Dismantling
Details of installation of components of transmission (section 1)
|
|
|
3 — AT case Pallet
3a — Laying
4, 7, 8, 108, 140 — Bolts
5 — the Oil filter
13 — the Lower cover
14 — the Big intermediate plate
15 — the Directing oil pipe |
98 — a gear shifting Cable
135 — the Fixing finger
142 — the Lock spring
151 — the Adjusting spring and lock laying
152 — the Blocking lever
Y3/2 — the Electromagnetic valve |
|
|
|
1. Remove the transmission from the rotation converter.
2. Remove a cable of gear shifting (98) with the vacuum drive.
3. Remove the electromagnetic valve (Y3/2).
4. Disconnect the transmission from arms.
5. Remove the case of valves (9).
6. Remove the lower cover (13) with an intermediate plate (14).
7. Remove single-channel valves, a brake tape of a brake B2, a maslootrazhatel and the temperature gate from the transmission case. |
|
Assembly
Assembly is carried out as it should be, the return to dismantling.
Section 2
Dismantling
Details of installation of components of transmission (section 2)
|
|
|
10 — the Forward cover with the secondary pump
17, 44a, 48 — Sealing rings
18, 45, 58, 73 — Bolts
19, 72 — Laying
20 — the Secondary pump
43 — the Lock ring
44 — the Ventilating stopper
46 — the Cover
|
50 — the Centrifugal regulator
59 — pressure modulator Valve
59a — the Finger
60 — pressure Modulator
62 — the Nut
4 — the Flange
70 — the Back cover of the transmission
S16/4 — the Switch of blocking of a starter |
|
|
|
1. Disassemble the transmission.
2. Remove the modulator (60).
3. Remove the switch of blocking of a starter (S16/4).
4. Remove the secondary pump (see the Section Removal, service and installation of the secondary pump (AT to No. 3652931)).
5. Remove a ventilating stopper (44) and a sealing ring (44a).
6. Remove a forward cover of the transmission (10) with the secondary pump (20).
7. Remove a flange (64).
8. Disconnect a lock ring (43), a cover (46) and a sealing ring (48).
9. Remove a back cover of the transmission (70).
|
|
Assembly
Assembly is carried out as it should be, the return to dismantling.
Section 3
Dismantling
Details of installation of components of transmission (section 3)
|
|
|
73 — the Plastic guide
74 — the Doggie of the parking brake
75 — Rastyazhnaya a spring
77 — the Sealing ring
82 — the Blocking plate with draft
82a — the Bolt
36 — the Output shaft |
165, 188 — the Lock ring
170 — the Crown gear wheel
172 — the Basic clutch plate of the raising transfer
192 — the Piston of coupling of the raising transfer
Y3/1x1 — the Stopper |
|
|
|
1. Disassemble the transmission (see sections 1 and 2).
2. Remove a rastyazhny spring (75) and unhook a doggie of the parking brake (74).
3. Take a plastic guide (73).
4. Remove a blocking plate (82) with draft, having turned off a bolt (82a).
5. Remove a stopper (Y3/1x1) of electromagnetic valves and a sealing ring (77) from the transmission case.
6. Remove a brake of the raising transfer and coupling.
|
|
Assembly
Assembly is carried out as it should be, the return to dismantling.
Section 4
Dismantling
Details of installation of components of transmission (section 4)
|
|
|
15 — B2 brake Piston
17 — B2 brake piston Cover
23, 41 — Lock rings
27 — the Brake tape of a brake B2
28 — the Finger
29 — B2 brake Bearing
30 — the Brake tape of a brake B1
31 — B1 brake Bearing
33, 60 — Bolts
34 — B1 Directing brakes
37 — B1 brake Piston
40 — B1 brake piston Cover
79 — the Basic flange
83 — Coupling of K1 |
85 — the Disk spring ring of a brake of LB3
87 — Planetary couple
88 — the Radial epiploon
88a — the Plastic directing B2 brake ring
90, 91, 197 — Sealing rings
95, 96 — Laying
97 — the Persistent bearing
100 — Coupling of K2
113 — Basic laying
115 — Teflon rings
133 — the Multidisk brake of B3
134 — the Damping spring
167 — the Output shaft
565 — the Sensor of protection of AT against an overload |
|
|
1. Disassemble the transmission (see sections 1, 2 and 3).
2. Take the bearing of a brake B1 (31) to them cases, having turned off a bolt (33) or the valve of protection of AT against an overload (S65). |
| 3. Attach a stripper (026) and tighten it on the transmission. Fix a stripper (026). Remove a lock ring (41). |
|
| 4. Weaken a stripper (026). Remove the piston with a finger of a brake of B1 (37) together with a cover (40) and the return springs (35) and (36). |
|
| 5. Take a guide of a brake tape of a brake of B1 (34). Replace a sealing ring in the transmission case. |
|
| 6. Remove coupling of K1 (83) with a brake tape of a brake B1 (30). Remove a multidisk brake of B3 (shooter). Carefully remove the leading shaft (87). |
|
7. Take a damping spring (134) from the transmission case.
8. Remove the piston of a brake B2 (15), having pressed a cover of a brake of B2 (17), having removed a lock ring (23).
9. Remove a plastic ring (88a) and a radial epiploon (88).
10. Remove coupling of K2 (100).
11. Shoot the brake film of a brake B2 (27).
12. Remove a basic ring (113) from a flange (79).
13. Remove a lock flange (79) from the transmission case, having turned off bolts (80). |
|
Assembly
|
|
|
1. Install a flange (79) with a sealing ring (197) and teflon rings (115) in the transmission case. Before installation of a flange (79), be convinced that the greasing constrictor is established in a flange (79), - for installation of a flange (79) use two bolts about 80 mm long.
2. Establish basic laying (113) on a flange (79).
3. Insert the bearing of a brake B2 (29) with a finger (20) into the transmission case. Bigger diameter of a finger (28) has to be directed to a brake tape of a brake B2 (27).
4. Insert the plastic directing ring (88a) and a radial epiploon (88) into the transmission case. At installation, the sealing edge has to be directed to a cover of the piston (17) of a brake tape.
|
| 5. Check a persistent part of a brake of B2 (29) for a curvature. A persistent part, an opening and an ear (shooters), at removal, have to settle down water and same situation. |
|
| 6. Install a new sealing ring in the transmission case. Insert a persistent part of a brake of B2 (29) an ear up. |
|
| 7. Squeeze a brake tape of a brake B2 (27) as far as it is possible and insert it into the case, - the brake tape can be established by means of a lock ring for the B2 (23) piston. |
|
| 8. Grease grooves on an output shaft (167) and insert teflon rings (167a). |
|
| 9. Establish coupling of K2 (100) on planetary couple by means of the device (030). |
|
10. Insert planetary couple into the transmission case, turning the leading shaft (87).
11. Install the transmission by an expert shaft (87) vertically up. |
|
| 12. Check installation of planetary couple. Planetary couple is established correctly when the upper edge of a connecting support (shooter) is lower, than a basic surface (138) of an external multidisk brake of LB3. Establish a spring (134). The ledge (arrow A) on a spring has to be established inside. The damping spring has to be installed in a groove (arrow B) in the transmission case. |
|
13. Install the piston of a brake B2 (15), having pressed a cover of the piston of a brake of B2 (17) and having inserted a lock ring (23).
14. Establish and check a gap in a multidisk brake of LB3.
15. Establish coupling of K1 (83) on planetary couple (87). |
| 16. Establish the brake film B1 (30). |
|
17. Check a gap of a brake tape of a brake of B1 (see the Section Measurement of a Gap in B1 brake) - the nominal rate makes 1.8-2.4 mm.
18. Check a gap in a brake tape of a brake B2, - the nominal rate makes 5.5-6.0 mm.
19. Check a gap in a multidisk brake of B3 (see the Section Installation and check of a gap in a multidisk brake of B3) - nominal rate makes 1.5 - 2.0 mm.
20. Further assembly is carried out as it should be, the return to removal. |
|
